Make your own paper plates plugin

  •  27 Comments
Make your own paper plates plugin

Show All Items This instructable will teach you how to apply cool images of your choice to your electrical switchplates. My wife and I like to have cool switch plates in our house.

Own make plugin plates your paper was

And usually we buy them from stores, or ebay. At that point I figured I was going to take matters in my own hands and make my own. Since then, I have made several of these here our own home and for gifts. What I have done is essentially backward engineer how to decorate these plates; they are very nice but perhaps not as polished as the truly professional ones. But this is an easy project that you can complete in just 3 or 4 hours, must of which is time make your own paper plates plugin for the glue to dry.

Things you need to make this instructable: Obtain a piece of suitable artwork yor you might like. If you find it online, tweak it in an imaging program like Photoshop, or MS Paint until you get a size that works with your plate. Plain copy paper works great for this project, but thin glossy paper is fine too. Thicker paper may work but you may need to soak it in water until it relaxes.

If you print your image, a LASER printer is ideal, an inkjet printer will work, but the quality may be inferior especially when it comes to the long term.

Plates plugin own make your paper research

I will show you examples of plates done with both. I would let images that you print yourself at least a few hours to dry before you proceed with the project. Step 2 Show All Items Hold papr plate and your image up to a light, find a good spot for the holes "own" fit in the picture, remove any excess of paper, you will need about half an inch of margin to fold around the back of the plate. Also brush on a coat of Mod Podge on the back of the read article and then apply the image onto the plate.

Use an overhead light again to see the alignment of the holes.

Be careful not to apply the sealer on too har Then it was time to let it dry completely. Stay tuned this week and next for tutorials and printables from this party! You could do this for a wedding and spend less than what it would cost to rent the plates. The foil image will come up with the transfer tape. That way you can fold the image around the hole for a more polished look. And follow us on Mske Tissue paper worked gorgeously. Learn more at Hands Occupied.

Step 4 Turn the plate around and carefully fold the image and cut off excess paper in the corner of the folds. Coat the rear of the plate with a nice thick coat of Mod Podge.

  • Once the tissue has been glued to the bottom of the plate, use a pair of sharp scissors to trim away the excess tissue paper.
  • With a fine arts degree, over 15 years experience in children's publishing, and a savvy, stylish, sassy tween daughter, I come armed with perspective and passion to inspire tween girls and their mothers to be crafty together.
  • Thicker paper may work but you may need to soak it in water until it relaxes.

Step 5 Show All Items Turn the plate around so you can see the front. Apply a nice thick coat of See more Podge all over the surface. Make your own paper plates plugin the image is covered, use your fingers and slide them over the surface of the image and work out any bubbles of air below.

Use the brush again and smooth the coat of Mod Podge. Perfection is not necessary, Mod Podge is very forgiving and you can touch up during the second coat. Step 6 Let the plate dry for about 2 hours, you can cover the brush with plastic wrap to keep the Mod Podge wet until the next coat, otherwise it will dry out. You could always wash the brush between coats. Step 7 Show All Items Once the first coat is dry, hold your plate up to the light and cut the screw holes.

For the switch hole, cut an X from corner to corner. That way you can fold the image around the hole for a more polished look. Step 8 Show All Items Turn the plate around and goop up the folds from the image center on to the back. As the paper absorbs the make your own paper plates plugin, it will remain stuck to the back.

Turn the plate and apply a second coat to the front. Step 9 Show All Items Let the plate dry for another two hours or overnight to be safe. Depending on the situation, you may want to paint the screws in a color that blends in with the image. In this please click for source, I aligned the screws in such a way that one screw would be completely white and the other black.


Make your own paper plates plugin

The black one I painted with a Sharpie nail polish or any other paint would work fine too. I include a picture of the plate from the instructable laser-printedanother plate done with an inkjet printed image, and another one from a calendar of vintage Spanish posters.


Making your Own Embossing Plates

I've also experimented with using postal stamps! Which is pretty cool, no need to print anything.

Newsletter

5 Comments
  1. Make your own paper plates plugin
    Mauk 27.07.2017 in 23:05

    The matchless message ;)

  1. Make your own paper plates plugin
    Kazishicage 29.07.2017 in 06:38

    What would you began to do on my place?

  1. Make your own paper plates plugin
    Vomuro 01.08.2017 in 09:21

    Yes, really. All above told the truth. Let's discuss this question.

  1. Make your own paper plates plugin
    Moogugore 11.08.2017 in 15:59

    I think, that you are mistaken. I can defend the position.

  1. Make your own paper plates plugin
    Shagami 20.08.2017 in 14:32

    I can not participate now in discussion - it is very occupied. I will be released - I will necessarily express the opinion.

Leave a Reply

*
*
* Minimum length: 20 characters