Iron on transfer paper for vinyl
Featured This post may contain affiliate links. If you purchase something through the link we may receive a small commission at no extra charge to you.
We really appreciate your support! When you get your first Silhouette machine, it can be overwhelming. That might even be an understatement.
iron on transfer paper for vinyl There is so much to learn and so much new terminology to wrap your head around. A few months back my friend Dawn from By Dawn Nicole and I started a Facebook group just for support with your Silhouette machine and to get some crazy awesome inspiration from 20, of your new best crafting friends. So I decided to do a Silhouette series where I talk about all the basic things you need to know when oon start.
Hobbies and for iron transfer paper on vinyl contact the
So make sure to pin this post for reference to your Silhouette Pinterest board and then come back often to learn more. What the basic idea of what we are doing here is taking pzper vinyl cut and using a sheet of transfer paper, also called transfer tape, to pick up the design and move it perfectly to the surface that you want to adhere it to.
It gets even link when the design is big or intricate. And then there is iron on transfer paper for vinyl whole issue of lining everything up just perfectly as you designed and cut it.
It would be almost iron on transfer paper for vinyl to do by hand. Now that makes sense, right?! Using transfer paper might sound a bit scary, but it is really super simple.
There are two main kinds of paper, clear and translucent. Although I am using the clear in this tutorial, I tend to prefer the translucent because it has grid lines that I think make it easier to keep your projects perfectly aligned.
Published paper iron vinyl transfer on for Essays
The first thing we are going to do is to weed the design. You can use a Silhouette hook tool to make the job super easy. You can see in the picture above, I am trying to put the names I cut in vinyl onto the water bottles in the top picture.
So in this case I weeded all of the excess vinyl, leaving iroh letters and the dot of the i. If I was making a stencil I would have done the opposite, by taking out the letters and leaving the excess to use as a stencil. I like to cut down the pieces of vinyl closely around the area I want to make weeding easier. Next you will want to cut your transfer paper roughly the same size as your piece of vinyl. Start foor peel off the backing and line up and stick that edge to your vinyl design as shown in the picture above.
You can then peel the backing off and stick down the rest of the transfer paper sticking it down as you peel. You could just peel the whole thing and stick it down, but I tend to get a lot of bubbles when I do that so this method works about x better for me!
Now before we start, make sure to do two important things: They also sell glitter HTV which I love for projects for my daughter! You can repin the Silhouette pin here! What the basic idea of what we are doing here is taking a vinyl cut and using a sheet of transfer paper, also called transfer tape, to pick up the design and move it perfectly to the surface that you want to adhere it to. It is the easiest to apply, without ln too much read more burning or shriveling. Read on to hear what I have learned along the way on Heat Transfer Vinyl, but first, let me make sure you know about my Silhouette series! We really appreciate your support!
Once you have the transfer tape on use a scraper tool, or an old gift card to scrape over the design to make sure the transfer tape is adhering to the vinyl nice and tight. Then slowly start to peel up your transfer tape at any corner.
As you peel, the vinyl should come off the backing with the transfer tape. Once you are done you should have the entire design you hope to transfer on the transfer tape and off of the backing. They can be tricky and are easy to miss!
You paper for on transfer iron vinyl reports
The only thing left to do now is apply your design to your project. Line up your design on your project and press the transfer tape firmly more info. Then get out your scraper tool again and score over the whole design to make sure that it adheres to the water bottle evenly and securely. Then start at any corner and peel back the transfer tape taking special care not to pull up any of the letters or small characters. Peel it back slowly until you reach the end and there you have it!
You just transferred your first vinyl design easy as that! If you love learning all about how to use your Silhouette machine I have a few more posts you just might love!